Centres

Revolving Centres (High Speed)

Body: Manufactured Out Of Fully Case Hardened Steel
*The Rotating Spindle Is Extended Till The Tail End & Ground 60 º Point Angle
* Needle Roller Bearing At The Tail End Carry All Radial Loads
* Heavy Duty Ball Thrust Bearing Takes All Axial Thrust
Max.Run Out : Within 0.007mm

CAT. NO.	SHANK	BODY DIA.Æ	OVERALL LENGTH (mm)
RC - HD2	MT - 2	50	128
RC - HD3	MT - 3	51	167
RC - HD4	MT - 4	66	214
RC - HD5	MT - 5	80	234

Quantity

Revolving Centres (Std. Speed)

Body: Alloy Steel Heat Treated In Single Piece Construction
Spindle: Chrome Carbon Steel Hardened,Tempered And Precision Ground 60 º Point Angle
Bearings : One Taper Roller Bearing Takes Thrust And Shares Radial Load With One Ball Bearing
Max Run Out: Within 0.010mm

CAT. NO.	SHANK	DIMENSIONS (mm)						H
CAT. NO.	SHANK	A	B	C	F	D	G	H
SRC - 1	MT - 1	18	27	37.5	56	40	0.5	45^o
SRC - 2	MT - 2	21	28	51	70	50	4.4	30^o
SRC - 3	MT - 3	24	33	57	86	59	5.2	30^o
SRC - 4	MT - 4	28	38	65	108	64	5.5	30^o
SRC - 5	MT - 5	36	43	80	136	79	7	30^o
SRC - 6	MT - 6	56	56	90	190	100	8	30^o

Quantity

Revolving Pipe Centres

* Live Centre For Machining Pipes And Similar Hollow Shaft Materials With A High Thrust Capacity
* Fully Hardened And Tempered alloy Steel Body
* Bevel Section Is Ground After Assembly Running In Its Own Bearing

CAT. NO.	SHANK	BEVEL DIAMETER (mm)		OVERALL LENGTH mm	ANGLE OF BEVEL
CAT. NO.	SHANK	MINIMUM	MAXIMUM	OVERALL LENGTH mm	ANGLE OF BEVEL
RPC - 2	MT - 2	19	80	135	75^o
RPC - 3	MT - 3	20	95	170	75^o
RPC - 4	MT - 4	29	125	200	75^o
RPC - 5	MT - 5	32	150	240	75^o

Quantity

Revolving Tube Centres

* Fully Hardened And Tempered Alloy Steel Body
* 60 º Cone Angle Is Presicion Ground

CAT. NO.	SHANK	CAPACITY
		MINIMUM		MAXIMUM
		INCHES	mm	INCHES	mm
RTC - 2A	MT - 2	1	26	2	50
RTC - 2B	MT - 2	1¹/₂	38	3	75
RTC - 3A	MT - 3	1	26	2	50
RTC - 3B	MT - 3	1¹/₂	38	3	75
RTC - 3C	MT - 3	2¹/₂	64	4	100
RTC - 4A	MT - 4	1	26	2	50
RTC - 4B	MT - 4	1¹/₂	38	3	75
RTC - 4C	MT - 4	2	51	3¹/₂	88
RTC - 4D	MT - 4	2¹/₂	64	4	100
RTC - 4E	MT - 4	3	76	6	150
RTC - 5A	MT - 5	2	51	3¹/₂	88
RTC - 5B	MT - 5	2¹/₂	64	4	100
RTC - 5C	MT - 5	3	76	6	150
RTC - 6A	MT - 6	2¹/₂	64	4	100
RTC - 6B	MT - 6	3	76	6	150
RTC - 6C	MT - 6	4	102	8	200

Quantity

Carbide Tipped Centres (Spanner Flat)

60 º Point Angle

* Made From High Carbon High Chromium Steel
* Fully Hardened Upto 58/62 HRC
* Carbide Tips Confirm To Prescribed Quality Standards
* 60 º Point Angle Is Precision Ground

CAT. NO.	SHANK	TAPER LENGTH (mm)	OVERALL LENGTH (mm)	MAX. DIA. Æ OF CARBIDE TIP (mm)
DC-CT1	MT - 1	57.5	80	6
DC-CT2	MT - 2	70	100	8
DC-CT3	MT - 3	86	125	11
DC-CT4	MT - 4	110	160	12
DC-CT5	MT - 5	136	200	14
DC-CT6	MT - 6	192	270	14

Quantity

Carbide Tipped Half Centre

(60 º Point Angle)

* Made From High Carbon High Chromium Steel
* Fully Hardened Upto 58/62 HRC
* Carbide Tips Confirm To Prescribed Quality Standards
* 60 º Point Angle Is Precision Ground

CAT. NO.	SHANK	TAPER LENGTH (mm)	OVERALL LENGTH (mm)	MAX. DIA. Æ OF CARBIDE TIP (mm)
DC-HC2	MT - 2	70	100	6
DC-HC3	MT - 3	86	125	8
DC-HC4	MT - 4	110	160	10
DC-HC5	MT - 5	136	200	12

Quantity

Carbon Steel Centres

* Made From High Carbon High Chromium Steel
* Fully Hardened Upto 58/62 HRC
* Carbide Tips Confirm To Prescribed Quality Standards
* 60 º Point Angle Is Precision Ground

CAT. NO.	SHANK	TAPER LENGTH (mm)	OVERALL LENGTH (mm)
DC-CS1	MT - 1	57.5	80
DC-CS2	MT - 2	70	100
DC-CS3	MT - 3	86	125
DC-CS4	MT - 4	110	160
DC-CS5	MT - 5	136	200
DC-CS6	MT - 6	192	270

Quantity